Electric Linear Actuator with Position Feedback
video

Electric Linear Actuator with Position Feedback

Conventional electric actuators often use limit switches to confirm the fully retracted and fully extended positions. When an application requires intermediate positioning or control of a valve or damper opening according to rod position, continuous position feedback is required. The Electric Linear Actuator with Position Feedback provides three feedback options for different control and accuracy requirements.
Send Inquiry
Product Introduction

Know Where It Stops

 

Conventional electric actuators often use limit switches to confirm the fully retracted and fully extended positions. When an application requires intermediate positioning or control of a valve or damper opening according to rod position, continuous position feedback is required. The Electric Linear Actuator with Position Feedback provides three feedback options for different control and accuracy requirements.


The potentiometer version provides a 0–5 V output with stated accuracy of ±1% of full stroke. It is the most economical option and suits applications that only require approximate position information, such as setting a damper to approximately 30% open.


The Hall encoder version provides a pulse output with stated accuracy of ±0.5% and a resolution of 0.1 mm. It provides a higher level of position feedback than the potentiometer option for applications that require position information without servo-level control.


The 4–20 mA analog version maps 4 mA to the fully retracted position and 20 mA to the fully extended position. The analog signal can be connected directly to a PLC analog input module for position monitoring and control.

product-800-800

 

Factory Calibration with a Precision Linear Grating Scale

 

 

The Electric Linear Actuator with Position Feedback follows the electric actuator requirements referenced in JB/T 12705-2016. It covers a thrust range of 500 N to 8000 N and a stroke range of 50 mm to 1000 mm. The feedback signal wiring is integrated into the factory-installed actuator cable, eliminating the need for a separate signal conduit.


For the waterproof configuration, the cable outlet provides IP65 protection. The specified repeat position accuracy ranges from ±0.5 mm to ±2 mm depending on the selected feedback configuration.


Each actuator is calibrated at a dedicated signal calibration station after assembly. The unit is mounted on a high-precision linear grating scale with a stated measurement accuracy of 0.01 mm. The actuator rod moves gradually from the fully retracted position while the grating scale records the actual rod position and the internal feedback signal is monitored simultaneously.


The measured points are compared to generate a calibration table, which is retained with the product certificate. If a position deviation occurs during field operation, the calibration data can be used to help determine whether the deviation is related to the feedback system or the PLC control settings. By integrating the position feedback function into the actuator, the system can avoid the cost and installation work associated with a separate external position sensor.

 

Specifications

 

Parameter

Content

Thrust range

500 N to 8000 N

Stroke range

50 mm to 1000 mm

Feedback type 1

Potentiometer, 0–5 V, ±1% of full stroke

Feedback type 2

Hall encoder, pulse output, ±0.5%, 0.1 mm resolution

Feedback type 3

Analog 4–20 mA, 4 mA fully retracted / 20 mA fully extended

Signal wiring

Integrated into the actuator cable

Waterproof cable outlet

IP65

Repeat position accuracy

±0.5 mm to ±2 mm, depending on feedback type

Factory calibration

Point-by-point calibration using a precision linear grating scale

Standard

JB/T 12705-2016

 

FAQ

 

 

Q: Which feedback type should I choose?

A: The potentiometer version is suitable for approximate position feedback. The Hall encoder version is suitable when pulse-based position feedback and higher resolution are required. The 4–20 mA version is suitable for direct connection to a PLC analog input.

Q: Can this actuator provide ±0.1 mm position accuracy?

A: This model is specified with repeat position accuracy from ±0.5 mm to ±2 mm depending on the feedback configuration. For applications requiring ±0.1 mm positioning accuracy, a servo actuator should be considered.

 

Hot Tags: electric linear actuator with position feedback, China electric linear actuator with position feedback manufacturers, suppliers, factory, Electric Telescopic Actuator, High Frequency Linear Actuator, Linear Electric Actuator with Control, Micro Electric Linear Actuator, Telescoping Electric Actuator, Waterproof Electric Linear Actuator

Send Inquiry

Home

Phone

E-mail

Inquiry