Waterproof Electric Linear Actuator
video

Waterproof Electric Linear Actuator

Many clients install electric actuators outdoors or on machines that are washed frequently. After a few months, the actuator may seize because water has entered through gaps around the rod and end cap. The inner bearing can rust, while moisture entering the motor winding can cause a short circuit. The Waterproof Electric Linear Actuator is designed for these wet operating conditions.
Send Inquiry
Product Introduction

No Water Gets In

 

Many clients install electric actuators outdoors or on machines that are washed frequently. After a few months, the actuator may seize because water has entered through gaps around the rod and end cap. The inner bearing can rust, while moisture entering the motor winding can cause a short circuit. The Waterproof Electric Linear Actuator is designed for these wet operating conditions. An IP65 version protects against water jets, so the housing and rod can be sprayed with a hose without allowing water to enter. An IP67 version provides protection during short-term immersion. It can be immersed in 1 meter of water for half an hour and continue to operate.
The entire body uses multiple sealing points. The end cap has an O-ring seal, the piston rod uses a double U-cup seal, and the cable outlet uses a waterproof rubber joint. Each seal is designed with a specific compression structure. If one seal gradually wears during long-term use, the other sealing points continue to provide protection against water ingress. The internal steel parts receive vacuum anti-rust treatment to reduce the risk of rust if a small amount of moisture enters the housing. The working temperature range is -20°C to +70°C. Typical applications include outdoor equipment, car wash equipment, fish farm equipment, and other wet environments.

product-800-800
 

Sealed Motor Without a Vent Hole

 

The motor uses fully sealed waterproof windings and has no vent hole. A conventional motor may use a vent hole for cooling and to balance internal and external air pressure, but the opening can also provide a path for water to enter. The sealed motor eliminates this opening and uses a larger housing surface area to improve heat dissipation. The Waterproof Electric Linear Actuator therefore maintains a sealed motor structure while providing the required operating performance in wet environments.

product-800-800

 

Hot Water Immersion Test on Every Unit

 

 

This product follows the electric actuator requirements of JB/T 12705-2016, while the enclosure protection class meets GB/T 4208-2017. Each assembled unit first runs without load for 10 minutes to generate heat inside the housing. It is then immersed directly in a 1-meter-deep water tank and continues running underwater for 10 minutes.


The immersion test is intended to simulate the negative pressure created by temperature changes. As the heated air inside the housing cools, it contracts and creates negative pressure. If the sealing structure is inadequate, outside water can be drawn into the housing. After the test, the housing is immediately dried and opened for inspection. Any visible water mark inside the unit is considered a failure, and the unit is returned for seal rework. We have followed this test procedure for 6 years and produce several hundred waterproof units each year. No unit has been returned from a customer site due to water damage.

 

Specifications

 

Parameter

Content

Protection options

IP65 (water jet protection) / IP67 (short-term immersion protection)

Seal structure

End cap O-ring + double U-cup rod seal + waterproof cable outlet joint

Inner anti-rust

Vacuum anti-rust treatment

Working temperature

-20°C to +70°C

Motor structure

Fully sealed waterproof winding, no vent hole

Thrust range

500 N to 8000 N

Stroke range

50 mm to 800 mm

Standard

JB/T 12705-2016, GB/T 4208-2017

Common uses

Outdoor equipment, car wash equipment, fish farm equipment, wet areas

Factory water test

Immersion in 1 m of water for 10 min while running; no internal water marks required for pass

 

FAQ

 

 

Q: What is the difference between IP65 and IP67?

A: IP65 protects against water jets from a hose. IP67 provides protection during short-term immersion in up to 1 meter of water. Our test procedure immerses the actuator in 1 meter of water while it is running.

Q: Why does the motor have no vent hole?

A: A vent hole can help with motor cooling and pressure balance, but it can also provide a path for water to enter. The sealed motor eliminates the vent hole and uses a larger housing surface area for heat dissipation.

 

Hot Tags: waterproof electric linear actuator, China waterproof electric linear actuator manufacturers, suppliers, factory, Compact Electric Linear Actuator, Electric Telescopic Actuator, High Force Electric Linear Actuator, Industrial Electric Linear Actuator, Micro Electric Linear Actuator, Telescoping Electric Actuator

Send Inquiry

Home

Phone

E-mail

Inquiry