3 Way Gravity Diverter Valve

3 Way Gravity Diverter Valve

The 3 Way Gravity Diverter Valve is installed at the discharge point of a conveyor belt. Material enters through the top inlet, and an internal flap directs the flow to either the left or right outlet. One inlet can therefore feed two discharge directions. When the downstream conveyor on one side requires material, the flap moves to that side.
Send Inquiry
Product Introduction

One Inlet, Two Outlets

 

The 3 Way Gravity Diverter Valve is installed at the discharge point of a conveyor belt. Material enters through the top inlet, and an internal flap directs the flow to either the left or right outlet. One inlet can therefore feed two discharge directions. When the downstream conveyor on one side requires material, the flap moves to that side. Standard square openings range from 300×300 to 1000×1000 mm, while round openings range from DN300 to DN1000. The diverter angle is available from 0 to 75 degrees or 0 to 90 degrees, with an adjustable switching angle and limit accuracy of ±0.5 degrees. The standard drive is a DYHQ hydraulic rotator, with torque from 250 to 2000 N·m depending on the opening size. The 90-degree switching time is 8 to 25 seconds, with larger openings requiring more time.

product-800-800

 

Thick Shell for Rough Material

 

 

The 3 Way Gravity Diverter Valve is manufactured according to GB/T 10595-2017 and JB/T 12705-2016. The standard shell thickness is 10 mm for normal powder and granular materials. For mining applications involving sand and gravel, the shell can be increased to 16 mm and fitted with an internal Mn13 high-manganese steel wear liner. The standard seal uses a rubber strip, with a leakage rate below 5%. For negative-pressure dust conveying systems that require tighter sealing, a double-seal configuration is available, reducing the leakage rate to below 2%. With a 500×500 mm opening, the handling capacity is 150–300 t/h for powder and 80–180 t/h for ore.

 

Shaft Alignment and Liner Welding

 

 

Flap shaft machining and wear-liner welding are key process steps for the 3 Way Gravity Diverter Valve. Bearings are installed at both ends of the flap shaft, and shaft alignment is controlled within 0.05 mm. Poor alignment can cause the flap to twist during operation and place additional radial load on the rotator output shaft, which can reduce service life. For liner welding, a wear-resistant welding electrode is used. The part is preheated to 200°C before welding, kept warm after welding, and then cooled gradually. Without preheating, the high-manganese steel liner is more likely to develop cracks around the weld seam, which can eventually cause the liner to detach during operation. This welding procedure is maintained as a standard workshop process requirement.

 

Specifications

 

Parameter

Content

Opening size

Square 300×300 to 1000×1000 mm / Round DN300 to DN1000

Diverter angle range

0–75 degrees / 0–90 degrees, limit accuracy ±0.5 degrees

Standard drive

DYHQ hydraulic rotator, torque 250–2000 N·m

90-degree switching time

8–25 s

Shell thickness

Standard 10 mm / Mining application 16 mm

Wear liner material

Mn13 high-manganese steel

Seal type

Rubber strip, leakage rate below 5%

Upgraded seal

Double seal, leakage rate below 2%, for negative-pressure applications

Capacity at 500×500 mm

Powder 150–300 t/h / Ore 80–180 t/h

Standards

GB/T 10595-2017, JB/T 12705-2016

Common materials

Aggregate, coal ash, grain, sand and gravel

 

FAQ

 

 

Q: Can I use this valve on a negative-pressure dust line?

A: Yes. The standard rubber-strip seal has a leakage rate below 5%. For tighter sealing, a double-seal configuration is available, with a leakage rate below 2%.

Q: Why does the shell thickness matter?

A: A thicker shell provides greater resistance to impact from abrasive materials. For mining applications involving sand and gravel, the 16 mm shell with an Mn13 high-manganese steel liner can be used.

 

Hot Tags: 3 way gravity diverter valve, China 3 way gravity diverter valve manufacturers, suppliers, factory, 3 Way Gravity Diverter Valve, 4 Way Gravity Diverter Valve, Jaw Gate, Rake Gate, Sector Gate, Silo Slide Gate

Send Inquiry

Home

Phone

E-mail

Inquiry