4 Way Gravity Diverter Valve
video

4 Way Gravity Diverter Valve

The 4 Way Gravity Diverter Valve has one more outlet than the three-way type. Material enters through the top inlet and can be directed to four outlets at the bottom. Two independent flaps control the flow paths, with each flap driven separately. They can operate at the same time or independently. For example, the left flap can direct material to port A while the right flap directs material to port C, allowing two discharge paths to operate at once.
Send Inquiry
Product Introduction

Four Outlets, Two Flaps

 

The 4 Way Gravity Diverter Valve has one more outlet than the three-way type. Material enters through the top inlet and can be directed to four outlets at the bottom. Two independent flaps control the flow paths, with each flap driven separately. They can operate at the same time or independently. For example, the left flap can direct material to port A while the right flap directs material to port C, allowing two discharge paths to operate at once. Different combinations of the four ports are also available. The opening size ranges from 400×400 to 1200×1200 mm, with four outlets of the same size. The switching structure uses two independent flaps and two DYHQ hydraulic rotators. Each rotator provides 500–2500 N·m of torque depending on the opening size. The action time difference between the two flaps is controlled within 1.5 seconds, with position accuracy of ±1 degree. Shell thickness ranges from 12 to 20 mm. Because the internal flow path is more complex than that of a three-way valve, all material flow paths are fitted with wear liners, rather than protecting only the main impact area.

product-800-800

Thicker Shaft on the Far Side

 

The 4 Way Gravity Diverter Valve is manufactured according to GB/T 10595-2017 and JB/T 12705-2016. The standard leakage rate is below 6%. For negative-pressure dust conveying systems, a double-seal air-lock configuration is available, reducing the leakage rate to below 1.5%. At a 600×600 mm opening, the total handling capacity for powder is 300–500 t/h. The factory also pays particular attention to synchronization between the two flaps. Synchronization depends not only on the control system but also on the mechanical structure. The two flap shafts have different lengths: one is positioned near the drive end, while the other extends farther from the drive end. The longer shaft has lower torsional stiffness, so its diameter is increased by one size to compensate. For example, the shaft near the drive end may use a 40 mm diameter, while the longer shaft uses 50 mm. This helps keep the torsional deformation of both shafts at a similar level under the same material impact, maintaining synchronized flap movement. Without this compensation, repeated material impact can gradually increase torsional deformation in the longer shaft and cause a larger timing difference between the two flaps during operation.

product-800-800

 

Specifications

 

Parameter

Content

Opening size

400×400 to 1200×1200 mm, four equal outlets

Switching structure

Two independent flaps, two hydraulic rotators

Single rotator torque

500–2500 N·m

Synchronization error

Action time difference between two flaps ≤1.5 s

Position accuracy

±1 degree

Shell thickness

12–20 mm

Wear liner

Fitted on all material flow paths

Standard leakage rate

≤6%

Double-seal leakage rate

≤1.5%, for negative-pressure dust applications

Capacity at 600×600 mm

Total powder feed 300–500 t/h

Standards

GB/T 10595-2017, JB/T 12705-2016

 

FAQ

 

 

Q: Can the two flaps work at the same time?

A: Yes. Each flap has an independent drive, so the two flaps can operate together or separately. Different combinations of the four outlets can be selected according to the material flow requirements.

Q: Why is the far shaft thicker?

A: The far shaft is longer and therefore has lower torsional stiffness. Its diameter is increased by one size to compensate for the difference in shaft length. This helps keep torsional deformation similar between the two shafts and maintains synchronized flap movement under material impact.

 

Hot Tags: 4 way gravity diverter valve, China 4 way gravity diverter valve manufacturers, suppliers, factory, 4 Way Gravity Diverter Valve, Ash Discharge Valve, Double Flap Airlock Valve, Rake Gate, Sector Gate, Silo Slide Gate

Send Inquiry

Home

Phone

E-mail

Inquiry